You will find details of my activity building the Bill Smith Hip Toggle Gearless Gravity Arm clock elsewhere on my site. This was the first clock I ever made and it taught me a lot about techniques all of which were well documented by Bill in his write up and in his many other books and videos.
Let me state now that the clock design as intended by Bill works and works well. It has one distinct disadvantage that every minute or so it gives a very loud ‘clunk’ as the pendulum amplitude diminishes, the hip toggle triggers and the solenoid resets. Running it in the workshop was fine as I became immune to the noise but sadly the clock will never progress into the house given my wife’s sensitivity to noise.
This has been a frustration to me as the clock looks splendid and its motion work action is a fascination to behold. It deserves to be on display in a more public arena than the workshop.
All of which lead to some head scratching and a compromise re-design. If I accept that the clock is an electro-mechanical device then my conscience allows me to consider other electro-mechanical solutions that are significantly less noisy. This is the fundamental premise to my re-design.
There are many clock designs that use magnetism attraction and repulsion as the driving force and my thoughts turned to this as a potential solution.
I 3D printed a magnet holder to fit on the pendulum rod. This holds two magnets. There is a large one facing the direction of swing and a small one perpendicular to the swing towards the backboard. I mounted a Hall Effect Sensor (HES) on a prototype board onto the back board at the mid swing position. The gist of my idea was to have the pendulum swinging back and forth across the HES with the HES being triggered by the small magnet. I would count the number of swings detected by the HES and after a defined number of swings I would energize a solenoid to repel the large magnet.
There was a little bit of electronics involved. I had a 4060 binary counter counting the swings and used the divide by 32 output to trigger a 555 in monostable mode. This would create a delay period from the mid point to the end of swing before the solenoid was energized. A second 555 would then define how long the solenoid repelling pulse would last. I also added LED indicators to all key timing points so I can easy diagnose what was going on. I also allowed selection of the 16,32 and 64 divisions from the 4060 until I established the optimum choice.
The pendulum period is 4800 beats per minute so one swing lasts for 750ms. The first 555 must therefore provide a delay of 375ms before energizing the solenoid. The second 555 delay would be a ‘suck it and see’ period to be determined.
The concept was lashed up and worked OK …. except that the pendulum amplitude just grew and grew until the large pendulum magnet attached itself to the solenoid core …. not a good idea . What was needed was a maximum amplitude detector to act as feedback to inhibit the solenoid pulse action.
A second HES was mounted at a position that represented the maximum swing position and the output from this, when triggered, would feed back to the 4060 RESET pin to stop the count until the amplitude diminished sufficiently. This worked and the result was very repeatable. There was one proviso that the pendulum must be started by triggering the over swing HES and releasing. Without this the 4060 could be one count out of step and would energize the solenoid as the pendulum was swinging back from its furthest point. This would cause a repelling and slowing of the swing.
The prototype has proved the concept but I now need to engineer a clean solution. First choice is perhaps an Arduino Mini but it could also be PIC based.
More to follow.
Similar or related subjects : –
- Microset Timer interface using Fusion 360 3D model with Fusion Electrical
- Clock adjuster rod for measuring spring and fusee drive power
- Update notes on modifications to the Devon Sea Clock
- A church clock problem and lockdown timekeeping
- Repairs to an ancient Thwaites clock completed
- Further 3D printed soft jaws for the Thwaites clock escape wheel
- Vice soft jaws and then soft soft vice jaws
- Workshop resources all coming together like clockwork
- Making a Brocot Escape Wheel using Fusion 360 and Tormach PCNC440 CNC milling machine
- Silencing the Bill Smith Gearless Gravity Arm Clock